VertiClip® SLD
This slide angle clip for drywall is used to connect metal studs at the head condition (top of wall) to the deck or primary structure while allowing for a total vertical deflection of up to 1½” (¾” up and ¾” down). TSN’s patented Step Bushing Technology provides an anti-friction and anti-seizure connection between the clip and the stud web surface.
Features
- ICC-ES Approved, report #ESR-2049
- NY MEA Approved, report #326-06-M
- UL classified for all approved dynamic assemblies and finish combinations with 1½” deflection and 1-2 hour fire-ratings
- Load-rated positive mechanical attachment at each stud
- Patented Step Bushing Technology provides friction-free motion for smooth vertical deflection
- Eliminates loose friction-held assemblies, heavy deep-leg track, & top row of wall bridging/strapping
- Load-rated #8 screws provided for vertical deflection connection to stud web
- Manufactured with certified, 50ksi, 33mil, G90 cold-formed steel
* VertiClip SLD is a component in VertiTrack® VTD, TSN’s pre-assembled deflection track.
Order Information
Qty/Box
SLD150
SLD250
SLD362/400
SLD600
SLD800
Lbs/Box
SLD150
SLD250
SLD362/400
SLD600
SLD800
Qty/Skid
SLD150
SLD250
SLD362/400
SLD600
SLD800
Lbs/Skid
SLD150
SLD250
SLD362/400
SLD600
SLD800
Nomenclature:
VertiClip SLD is designated by type (SLD), followed by stud depth in inches multiplied by
100.
Example: 6″ stud
Designate: VertiClip® SLD
Material Composition
ASTM A1003/A1003M Structural Grade 50 (340) Type H, ST50H (ST340H): 50ksi (340MPa) minimum yield strength, 65ksi (450MPa) minimum tensile strength, 33mil minimum thickness (20 gauge, 0.0346” design thickness) with ASTM A653/A653M G60 (Z180) hot dipped galvanized coating.
Catalogs
TSN’s Product Catalogs are an essential resource for the design of cold formed steel. Developed by Engineers, the catalogs contain design data for members, connectors, and fasteners. VertiClip® SLD can be found in the following Catalogs:
For a full list of our product catalogs, specification sections, inspection checklists, and research reports please click here.
VertiClip® SLD Downloads
VertiClip® SLD Applications
VertiClip SLD comes in a 1½” and 3″ deflection option. The attachment of VertiClip SLD to the primary structure may be made with a PAF, screw/bolt anchors or weld and is dependent upon the base material (steel or concrete) and the design configuration.
1½” Deflection - Interior or Exterior Head of Wall
Installation Instructions
- Attach standard leg runner track to deck.
- Attach VertiClip SLD to deck (through track).
- Attach VertiClip through Step Bushings to wall studs with self-drilling screws provided.
Allowable Loads
Notes:
- Fasten within ¾” from the angle heel (centerline of the 1½” leg) to minimize eccentric load transfer.
- Guide holes for attachment to structure are 0.141″ for SLD362/400 and SLD600, and are not standard for other clip sizes.
- Total vertical deflection of up to 1½” (¾” up and ¾” down). Deflection requirements greater than ¾” (up and down) are available.
- VertiClip SLD series is designed to support horizontal loads and should not be used in axial-load-bearing wall construction.
- Allowable loads have not been increased for wind, seismic, or other factors.
- #8 screws are provided with each VertiClip SLD step bushing.
- Strengthening ribs are present in 3 5/8″ and 6″sizes.
- For LRFD Design Strengths refer to ICC-ESR-2049.