VertiTrack® VTD
Features
- ICC-ES Approved, report #ESR-2049
- NY MEA Approved, report #326-06-M
- UL classified for all approved dynamic assemblies and finish combinations with 1½” deflection and 1-2 hour fire-ratings
- Pre-installed clip saves time installing clips and spacing studs
- Load-rated positive mechanical attachment at each stud
- Patented Step Bushing Technology provides friction-free motion for smooth vertical deflection
- Eliminates loose friction-held assemblies, heavy deep-leg track, & top row of wall bridging/strapping
- Load-rated #12 screws provided for vertical deflection connection to stud web
- Manufactured with certified, 50ksi, G90 coated cold-formed steel
Order Information
Lbs/Piece
VTD250-16
VTD250-24
VTD362-16
VTD362-24
VTD400-16
VTD400-24
VTD600-16
VTD600-24
VTD800-16
VTD800-24
Qty/Skid (Pieces)
VTD250-16
VTD250-24
VTD362-16
VTD362-24
VTD400-16
VTD400-24
VTD600-16
VTD600-24
VTD800-16
VTD800-24
Qty/Skid (Feet)
VTD250-16
VTD250-24
VTD362-16
VTD362-24
VTD400-16
VTD400-24
VTD600-16
VTD600-24
VTD800-16
VTD800-24
Lbs/Skid
VTD250-16
VTD250-24
VTD362-16
VTD362-24
VTD400-16
VTD400-24
VTD600-16
VTD600-24
VTD800-16
VTD800-24
Nomenclature:
VertiTrack VTD is manufactured in 12 ft. lengths. VertiTrack is designated by type (VTD), followed by stud depth in inches multiplied by 100 and stud spacing.
Example:6″ deep stud, 16″ on center
Designate:VertiTrack® VTD600-16
Material Composition
Clip Material: ASTM A1003/A1003M Structural Grade 50 (340) Type H, ST50H (ST340H): 50ksi (340MPa) minimum yield strength, 65ksi (450MPa) minimum tensile strength, 33mil minimum thickness (20 gauge, 0.0346” design thickness) with ASTM A653/A653M G60 (Z180) hot dipped galvanized coating.
Track Material: ASTM A1003/A1003M Structural Grade 33 (230) Type H, ST33H (ST230H): 33ksi (230MPa) minimum yield strength, 45ksi (310MPa) minimum tensile strength, 33mil minimum thickness (20 gauge, 0.0346” design thickness) with ASTM A653/A653M G60 (Z180) hot dipped galvanized coating.
Catalogs
TSN’s Product Catalogs are an essential resource for the design of cold formed steel. Developed by Engineers, the catalogs contain design data for members, connectors, and fasteners. VertiTrack® VTD can be found in the following Catalogs:
For a full list of our product catalogs, specification sections, inspection checklists, and research reports please visit our Catalogs & Design Guides page.
VertiTrack® VTD Downloads
VertiTrack® VTD Applications
The attachment of VertiTrack VTD to the primary structure may be made with PAFs, screw/bolt anchors or weld and is dependent upon the base material (steel or concrete) and the design configuration.
1½” Deflection - Interior or Exterior Head of Wall
Installation Instructions
- Attach VertiTrack VTD to deck with approved fasteners.
- Attach VertiClip through Step Bushings to wall studs with self-drilling screws provided.
Allowable Loads
Notes:
- VertiTrack VTD loads are the same as VertiClip® SLD
- VertiTrack VTD is assembled with VertiClip SLD pre-attached at 16″ o.c. and 24″ o.c.
- Total vertical deflection of up to 1½” (¾” up and ¾” down). Deflection requirements greater than ¾” (up and down) are available.
- Custom spacing is also available.
- Fasten within ¾” from the angle heel (centerline of the 1½” leg) to minimize eccentric load transfer.
- Fasten through each VertiClip SLD to structure.
- VertiTrack VTD series is designed to support horizontal loads, and should not be used in axial-load-bearing walls.
- Allowable loads have not been increased for wind, seismic, or other factors.
- #8 screws are provided with each step bushing for attachment to the stud web.
- Strengthening ribs are present in 3 ⅝ and 6″sizes.